#Show mac address fortinet serial number#
#Show mac address fortinet update#
#Show mac address fortinet Offline#

It is always “diagnose sys” but “execute system”. It is “ get router info6 routing-table” to show the routing table but “ diagnose firewall proute6 list” for the PBF rules. With Fortinet you have the choice confusion between show | get | diagnose | execute.

#Show mac address fortinet update#

I am using it personally as a cheat sheet / quick reference and will update it from time to time.Ĭoming from Cisco, everything is “show”. I am more focused on the general troubleshooting stuff. These must only be used if there are really specific problems. I am not focused on too many memory, process, kernel, etc. It is not complete nor very detailled, but provides the basic commands for troubleshooting network related issues that are not resolvable via the GUI. Note that get, execute, and diagnose commands are also available.This blog post is a list of common troubleshooting commands I am using on the FortiGate CLI. The FortiAuthenticator VM's console allows scrolling up and down through the CLI output by using Shift+PageUp and Shift+PageDown.Īnother tip to be aware of is, exactly like FortiOS, the ? key can be used to display all possible options available to you, depending upon where you are hierarchically-situated. The following initial-setup commands have been introduced to FortiAuthenticator note that all existing CLI commands found in the FortiAuthenticator now fall under the following: With the release of version 5.0, FortiAuthenticator's CLI commands (concerning basic configuration) have become more similar to other product's CLI, such as the commands commonly found in FOS. Same as tcpdump, but the output is written to a downloadable file that can be downloaded in the debug logs.ĭebug logs can be accessed by using your web browser to browse to For more information, see Debug logs.Įxamine the route taken to another network host. Test network connectivity to another network host.

#Show mac address fortinet serial number#

This procedure deletes all changes that you have made to the FortiAuthenticator configuration and reverts the system to its original configuration, including resetting interface addresses.ĭisplay basic system status information including firmware version, build number, serial number of the unit, and system time.ĭisplay general hardware status information.ĭisplay disk hardware status information.ĭisplay RAID hardware status information. This includes clearing the user database.

#Show mac address fortinet Offline#

The unit will go offline and there will be a delay while it restarts.Įnter this command to reset the FortiAuthenticator settings to factory default settings.

Perform a hard restart of the FortiAuthenticator unit. Restore factory reset's admin access settings to the port1 network interface. Rebuild the configuration database from scratch using the HA peer's configuration. For each set command listed above, there is an unset command, for example unset port1-ip. Select the types of administrative access to allow.Įnter the level for HA service debug logs. Usually, you should assign addresses on the same private subnet. The two units must have different addresses. Normally, the unit with High priority is the master unit.Įnter the IP address, with netmask, that this unit uses for HA related communication with the other FortiAuthenticator unit. Set to Low on one unit and High on the other. Both units must use the same interface for HA communication. This interface must not already have an IP address assigned and it cannot be used for authentication services. Select a network interface to use for communication between the two cluster members. To see a list of index numbers and their corresponding time zones, enter set tz ?. For example 15:10:00 is 3:10pm.Įnter the current time zone using the time zone index. Valid format is two digits each for hours, minutes, and seconds. For example: set date sets the date to August 12th, 2014.Įnter the current time.

Valid format is four digit year, two digit month, and two digit day. This is the default route for this interface.Įnter the current date. Once this port is configured, you can use the GUI to configure the remaining ports.Įnter the IPv4 address of the default gateway for this interface. Netmask is expected in the /xx format, for example 192.168.0.1/24. You can also enter ? for help.Įnter the IPv4 address and netmask for the port1 interface. The commands can be used to initially configure the unit, perform a factory reset, or reset the values if the GUI is not accessible.ĭisplay list of valid CLI commands. The FortiAuthenticator has CLI commands that are accessed using SSH or Telnet, or through the CLI Console if a FortiAuthenticator is installed on a FortiHypervisor.